BISOPE series 66 How to set the appropriate frequency for measurement S...

BISOPE series 66- How to set the appropriate frequency for measurement (Setting the maximum frequency for vibration measurement)

-------------------------------------------------------------------------------------------------------------

If you measure vibration using an FFT vibration meter, there are many things to consider in advance compared to measuring other physical quantities (temperature, displacement, pressure, etc.). Above all, the most difficult question at first is “How many Hz should I set?” However, if you have a simple vibration meter, you don’t have to worry much. This is because general vibration meters cannot perform FFT processing (they only use the time waveform without frequency setting itself and use the appropriate filtering to cut out the area that can be measured). However, FFT meters are different. If you set the frequency incorrectly, you may not be able to see the desired signal at all, and since it is a fundamental problem, it can be difficult.

 

Frequency setting (maximum frequency Fmax and sampling frequency)

 

When setting the frequency for vibration measurement, you basically set the maximum frequency (Fmax). This means the highest frequency on the horizontal axis of the spectrum graph. In the past, advanced FFT types expressed this as sampling frequency (sampling rate), which is usually twice the Fmax in vibration measuring instruments. To be exact, it is 2.56 times, but it is set to 2 times. Therefore, if you ask about the sampling frequency, you can divide the maximum frequency by 2. However, it is not important to enter the setting value, but to think in advance about, for example, 'What can I see if I set Fmax to 1000 Hz?'. See below.

 

#vibration measuring instrument, #frequency setting, #Fmax, #maximum frequency, #sampling frequency, #sampling rate, #FFT, #3-axis vibration sensor, #acceleration sensor, #vibration education, #building vibration, #vibration measurement, #resonance analysis, #resonance measurement, #vibration monitoring, #vibration noise consulting  www.kCBM.kr,   https://blog.naver.com/vs72 , https://contents.premium.naver.com/bisope/visope

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BISOPE series 51 How to set the appropriate frequency when measuring se...

BISOPE series 51- How to set the appropriate frequency when measuring (setting the maximum frequency for vibration measurement)

-------------------------------------------------------------------------------------------------------------

When measuring vibration using an FFT vibration measuring instrument, there are more things to consider in advance than measuring other physical quantities (temperature, displacement, pressure, etc.). Above all, the most difficult question at first is “How many Hz should I set it to?” However, if you have a simple vibration system, you don't need to worry much. This is because FFT processing is not possible in general vibration systems (the area that can be measured using only the time waveform without setting the frequency itself is cut out using appropriate filtering). However, FFT instruments are different. If you set the frequency incorrectly, you may not be able to see the desired signal at all, and it may be embarrassing because it is a basic problem.

 

​Frequency setting (maximum frequency Fmax and sampling frequency)

 

When setting the frequency for vibration measurement, you basically need to set the maximum frequency (Fmax). This means the highest frequency on the horizontal axis of the spectrum graph. In advanced FFT types of the past, this was expressed as sampling frequency (Sampling rate), which is usually twice the Fmax in vibration measuring instruments. To be exact, it is 2.56 times, but it is set at 2 times. Therefore, if you are asking about the sampling frequency, just divide the maximum frequency by 2. However, it is not important to enter the setting value, but for example, 'What can I see if I set Fmax to 1000Hz?' The most important thing is to think about it in advance. See below.

 

 

In other words, determine the maximum frequency after determining the following matters. Above all, the most basic principle is that the frequency group to be checked must be measured and placed so that it is visible in the center of the screen.

​

1. Determine the specifications of the machine

 

-Rotation speed of the prime mover (drive component) (number of poles of the motor, electric frequency, number of blades of the turbine, sleeve rolling bearing, and other rotating elements)

-Sleev

​https://blog.naver.com/vs72

#Vibration measuring instrument, #frequency setting, #Fmax, #maximum frequency, #sampling frequency, #Sampling rate, #FFT, #3-axis vibration sensor, #acceleration sensor, #vibration education, #building vibration, #vibration measurement, #resonance analysis , #resonance measurement, #vibration monitoring, #vibration noise consulting